Ositech-comm Trumpcard Data/Fax Modem Manuel d'utilisateur Page 71
- Page / 86
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
User’s Guide and Reference 4 - 39
Modem Command Reference
Default 2
Sets the length of time to pause when the modem encounters the "Pause
During Dial" call progress feature, i.e., the comma (,).
S9 — Carrier Detect Response Time
Range 1-255 tenths of second
Default 6 (0.6 seconds)
Determines how long a carrier signal must be present before the modem
recognizes it as a carrier and turns on /RLSD. As this time is increased,
there is less chance to detect a false carrier due to noise from the telco
line.
S10 — Lost Carrier To Hang Up Delay
Range 1-255 tenths of a second
Default 14 (1.4 seconds)
Sets the length of time the modem waits before hanging up after a loss of
carrier. This allows for a temporary carrier loss without causing the local
modem to disconnect. When register S10 is set to 255, the modem
functions as if carrier is always present.
The actual interval the modem waits before disconnecting is the value in
register S10 minus the value in register S9. Therefore, the S10 value must
be greater than the S9 value or else the modem disconnects before it
recognizes the carrier.
S11 — DTMF Tone Duration
Range 50-255 milliseconds
Default 95 milliseconds
Sets the duration of tones in Dual Tone Multifrequency (DTMF) dialling.
This value has no effect on pulse dialling.
S12 — Escape Code Guard Time
Range 0-255 fiftieths of a second
Default 50 (1 second)
Sets the time delay required immediately before and after entering the
escape code. The time interval between the sending of the first and
second, or the second and the third escape code characters must be less
than the value of the guard time.
- Trumpcard Data/Fax Modem 1
- User’s Guide and Reference 1
- Copyright 2
- How To Contact Us 2
- Contents 8
- Modem Command Reference 4-1 9
- Modem Test Procedures 5-1 9
- Introduction 11
- Features 12
- Facsimile Mode 13
- Cellular Mode 13
- Unique Features 14
- Industry Standards 15
- Section One 16
- Hardware Installation 17
- Preparing for Installation 17
- Installing the Trumpcard 18
- Section Two 20
- Basic Modem Operation 21
- Before You Begin 22
- Operating the 23
- Making an Outgoing Call 24
- Re-Dialling the Last Number 25
- Storing a Number 25
- Connection Messages 25
- Section Four 26
- Ending Your Connection 27
- Connection 27
- Receiving an Incoming Call 28
- Cellular Phone Configuration 30
- Outgoing Cellular Call 30
- Incoming Cellular Call 30
- Cellular Call Status 31
- Modem Command Reference 33
- Modem Command Guidelines 34
- Modem Command Summary 36
- Modem Command Descriptions 38
- Bn — Set ITU-T or Bell Mode 39
- Dn — Dial 39
- Examples 40
- En — Command Echo 41
- Sub-parameter Definitions 42
- Hn — Switch-Hook Control 43
- In — Identification 44
- Ln — Speaker Volume 44
- Mn — Speaker Control 44
- Nn — Automode Detection 45
- P — Set Pulse Dial as Default 46
- Qn — Result Code Display 46
- Sn — Read/Write S Registers 46
- T — Set Tone Dial as Default 47
- Vn — Result Code Form 47
- Wn — Connect Message Control 47
- Xn — Extended Result Codes 48
- Section Four 50
- Zn — Reset 51
- &Cn — DCD Option 51
- &Dn — DTR Option 52
- &Gn — Set Guard Tone 53
- &Ln — Line Type 54
- &Mn — Communication Mode 54
- &Qn — Communication Mode 54
- &Rn — RTS/CTS Option 55
- &Sn — DSR Option 55
- &Tn — Test and Diagnostic 56
- &Wn — Store User Profile 58
- \Bn — Transmit Break 59
- \Kn — Break Control 59
- \Nn — Operation Mode Control 61
- %Cn — Compression Control 61
- -Kn — MNP Extended Services 63
- *Hn — Link Negotiation Speed 63
- :En — Compromise Equalizer 64
- Modem S Registers 66
- Modem Register Summary 66
- Register Descriptions 69
- S5 — Backspace Character 70
- S11 — DTMF Tone Duration 71
- S12 — Escape Code Guard Time 71
- S18 — Test Timer 72
- S24 — Sleep Inactivity Timer 72
- S25 — Delay to DTR 72
- S30 — Inactivity Timer 72
- S32 — XON Character 73
- S33 — XOFF Character 73
- S36 — LAPM Failure Control 73
- S46 — Protocol Selection 75
- S48 — V.42 Negotiation Action 76
- S95 — Extended Result Codes 77
- Facsimile Commands 78
- Modem Test Procedures 79
- Local Modem Self-Test 80
- Local Analog Loopback 81
- Generated Pattern 82
- Remote Digital Loopback 83
- Local Digital Loopback 85
- Testing Modem Memory 86
Produits connexes et manuels pour Matériel Ositech-comm Trumpcard Data/Fax Modem
(54 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.421 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels